GSBoxPC840_e.pdf

SIMATIC

Box PC 840

Getting Started

Edition 03/2002

Safety guidelines

This Getting Started contains notices intended to ensure personal safety, as well as to protect the products and

connected equipment against damage. These notices are highlighted by the symbols shown below and graded

according to severity by the following texts:

Danger

indicates that death, severe personal injury or substantial property damage will result if proper precautions are not

taken.

Warning

indicates that death, severe personal injury or substantial property damage can result if proper precautions are not

taken.

Caution

indicates that minor personal injury can result if proper precautions are not taken.

Caution

indicates that property damage can result if proper precautions are not taken.

Notice

draws your attention to particularly important information on the product, handling the product, or to a particular

part of the documentation.

Qualified Personnel

Repair, maintenance and servicing of device only to be carried out by qualified personnel. Qualified persons are

defined as persons who are authorized to commission, to ground, and to tag circuits, equipment, and systems in

accordance with established safety practices and standards.

Correct Usage

Note the following:

Warning

This device and its components may only be used for the applications described in the catalog or the technical

description, and only in connection with devices or components from other manufacturers which have been

approved or recommended by Siemens.

This product can only function correctly and safely if it is transported, stored, set up, and installed correctly, and

operated and maintained as recommended.

Trademarks

SIMATIC

are registered trademarks of Siemens AG.

Third parties using for their own purposes any other names in this document which refer to trademarks might in-

fringe upon the rights of the trademark owners.

, SIMATIC HMI

and SIMATIC NET

The reproduction, transmission or use of this document or its

contents is not permitted without express written authority.

Offenders will be liable for damages. All rights, including rights

created by patent grant or registration of a utility model or design, are

reserved.

!"#$$%&

Disclaim of Liability

We have checked the contents of this manual for agreement with the

hardware and software described. Since deviations cannot be pre-

cluded entirely, we cannot guarantee full agreement. However, the

data in this manual are reviewed regularly and any necessary cor-

rections included in subsequent editions. Suggestions for improve-

ment are welcomed.

Siemens AG 2001-2002

Technical data subject to change.

Siemens Aktiengesellschaft

"""'!'$

This Getting Started offers you step by step instructions on how to install and start the SIMATIC

Box PC 840.

Unpacking the SIMATIC Box PC 840

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing the SIMATIC Box PC 840

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hardware Components of the SIMATIC Box PC 840

. . . . . . . . . . . . . . . . . . . . . .

Connection to the Power Supply Unit

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Powering Up the SIMATIC Box PC 840

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Switching Off the SIMATIC Box PC 840

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Reinstallation of the Software

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Error Diagnosis

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Further Support and Sales Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Certificates, Directives and Declarations

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The references to the manual are intended to give you an initial overview of the information in the

manual.

Electronic Manual

You can find the electronic manual on the included CD ÑDocumentation and DriversÒ under the file

name ÑHBBoxPC840_b.pdfÒ. The manual offers information on many useful topics, for example,

optional hardware-expansion, modification of the device configuration and technical data.

To read or to print out the manual you need the Adobe Acrobat Reader. The Adobe software is

preinstalled on the PC as well as on the CD ÑDocumentation and DriversÒ.

Warning

To avoid damage to assets and for the sake of your own personal safety, please take note of the

information on safety in this user guide and in the electronic manual. These notes are highlighted

with triangular warning signs. They are presented in different ways and in accordance with the

degree of risk.

Unpacking the SIMATIC Box PC 840

Unpack your SIMATIC Box PC 840 as follows:

1. Remove the Box PC 840 from the packaging.

2. Do not throw the original packing away. Keep it in case you have to transport the unit again

sometime in the future.

Checking the Contents

3. Check with the packing list to make sure no components are missing.

4. Check the packing and its contents for any shipping or transport damage.

5. Please inform your local dealer of any shipping or transport damages and of outstanding items

indicated on the packing list.

Caution

Risk of mechanical damage of your device!

When transporting your PC in cold weather, when it may be exposed to extreme variations

in temperature, make sure that no moisture or condensation can form on or in the unit.

The unit should be allowed to reach room temperature slowly before it is started up. If

condensation has formed, the unit should be left for about 12 hours before being switched on.

Getting Started Box PC 840

A5E00085986-02

Recording the Serial Number and the Ethernet address

Enter the serial number and the Ethernet address of your PC in the table below. You can find

the serial number on the type label attached above the device fan. The Ethernet address can be

found in the BIOS setup settings in the main menu under the ÔHardware OptionsÔ function.

The device can precisely be identified with the help of these numbers in case of repairs or theft.

Enter the Microsoft Windows ÑProduct KeyÒ from the ÑCertificate of AuthenticityÒ

Enter the Microsoft Windows ÑProduct KeyÒ from the ÑCertificate of AuthenticityÒ (COA) in the

table. You will find the ÑProduct KeyÒ on the device. You need the Windows ÑProduct KeyÒ if you

want to reinstall the operating system.

Serial number

Order No.

Microsoft Windows Product Key

Ethernet Address

Installing the SIMATIC Box PC 840

The SIMATIC Box PC 840 can be operated in several positions. It is particularly suitable for fitting in

consoles, switch boards and control panels.

The SIMATIC Box PC 840 with AC power supply meets the requirements for a fire enclosure to

EN60950. it can therefore be fitted without an additional fire enclosure.

The SIMATIC Box PC 840 with DC power supply is an open device (fan side); therefore the

mounting must meet the requirements of a fire enclosure.

Warning

Only connect the device to 24V DC power supply systems which meet the requirements of a safe

extra-low voltage (SELV); in addition, a protective conductor must be connected.

The cable cross section has to be large enough that the Box PC will not be damaged by the cables

when there is a short circuit.

Please note the following points when installing the PC:

•

Avoid extreme ambient conditions as far as possible. Protect your PC from dust, moisture, and

heat.

•

Keep the PC out of direct sunlight.

•

Mount the PC as safely as possible to prevent any danger (for example, by falling over).

•

The clearance around the housing must be at least 100 mm at the front and rear, so that the PC is

sufficiently ventilated.

Make certain that the ventilation slots for the housing are not covered.

•

Observe the permissible fitting positions without fail when installing the systems.

•

Getting Started Box PC 840

A5E00085986-02

Depending on the configuration of the device, two mounting brackets are included in the scope of

delivery. You can attach these to the housing with 6 screws (M3x6).

M3 thread, max. depth of engagement 5 mm

Instructions for Fixing the SIMATIC Box PC 840 to the Wall or to the Ceiling

To install the SIMATIC Box PC 840 in a concrete wall or ceiling proceed as follows:

1. Fix the mounting brackets at the housing of the PC.

2. Drill four holes of 8 mm diameter and 60 mm depth into the wall or ceiling. You will find the

required dimension drawings on the following pages.

3. Insert the concrete plugs (8 mm diameter and 50 mm long) into the drill holes.

4. Fix the PC with four screws (4 mm diameter and 50 mm long).

In a plasterboard wall or ceiling (min. 13 mm thick), drill holes of 14 mm diameter and fasten the PC

with four anchors (4 mm diameter and 50 mm long).

In a metal sheet wall or ceiling (min. 2 mm thick), drill holes of 5 mm diameter and fasten the PC with

four screws (4 mm diameter and min. 15 mm long).

Warning

The installer must verify that the wall or ceiling can support four times the full load of the SIMATIC

Box PC 840 (with mounting brackets and expansion modules). The total weight is approx. 10 kg.

Getting Started Box PC 840

A5E00085986-02

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: