EVBST7_01_en.pdf
(
1194 KB
)
Pobierz
EVBST7-0 1
Evaluation board for
Microcontrollers, series ST7Lite0 and ST7SuperLite.
R
User’s
manual
Many ideas one solution
REV 1.2
1. Introduction
EVBST7-01-XXX
is a development board designed for the hobbyists and engineers,
who want to quickly prototype their system based on LITE0 and LITES family of
microcontrollers from ST Microelectronics. Developer has an access to all the pins of
the micro, which are brought to the header (pin connectors) and labeled accordingly.
Depending upon board’s configuration (listed versions) some or all of the following
components are found on the board: analog thermometer, potentiometer, relay,
buzzer, RTC (real time clock) and LCD display (2x16). Provided pin headers allow
easy access to all of these components. In addition, there are four micro-switches
and eight diodes, which could be connected to any of the pin connectors or additional
components, which may be placed on the large, adjacent prototype area. Board’s
power circuitry (bridge, voltage regulator) eliminates the need for an external
regulated power supply. This board comes with the several examples of the C code
routines (source form), to facilitate testing and quick development in using board’s
resources.
We wish you a lot of success and full satisfaction, while designing
and constructing appliances based on EVBST7-01-XXX
2
2. Board layout
1. Prototype area
2. Additional components connector
3. LED’s and micro-switches
4. Potentiometer (may be connected to the ADC of the processor)
5. LM35 thermometer
6. RESET micro-switch and power supply LED
7. 2x16 display (optional)
8. Buzzer
9. LM317 voltage regulator
10. Power ON/OFF switch
11. Input power jack (AC/DC)
12. Relay header
13. Programmer header
14. Dual header – port A, port B
15. Socket for processors LITE02, 05, 09 and LITES2, S5
16. Standard LCD display connector
17. Socket for lithium battery
18. M41T00 real time clock (optional)
3
3. Supported microcontrollers
ST7SUPERLITE
ST7LITE0
ST7LITES2
ST7LITES5
ST7LITE02
ST7LITE05
ST7LITE09
FLASH
1kB
1kB
1.5kB
1.5kB
1.5kB
RAM(stos)
128(64)B
128(64)B
128(64)B
128(64)B
128(64)B
EEPROM
-
-
-
-
128B
Peripherals
LT Timer/Wdg,
AT Timer/1
PWM,
SPI
LT Timer/Wdg,
AT Timer
/1PWM,
SPI, 8-bit ADC
LT Timer/Wdg,
AT Timer
/1PWM,
SPI
LT Timer/Wdg,
AT Timer
/1PWM,
SPI, 8-bit ADC
LT Timer/Wdg,
AT Timer /1 PWM,
SPI, 8-bit ADC/op AMP
Voltage
supply
2.4V – 5.5V
Clock
frequency
1MHz RC 1% + PLLx4/8MHz
Temperature
range
from -40ºC to 80ºC
Cases
SO16 150”, DIP16
4. Power supply
Recommended external power supply voltage is 7-12V AC, or 9-15V DC. Standard
power jack (bolt diameter 2.1mm - negative) is provided at the edge of the board.
Stabilized voltage Vdd is accessible on the double header and on the prototype area
of the board. The selection of the Vdd is provided thru 3V3 header. The default
voltage Vdd is 5VDC (no jumper on 3V3 header). By placing a jumper Vdd becomes
3.3 VDC. The SUPPLY header allows for the direct access to the power jack input.
Placing a jumper bypasses the bridge and voltage regulator.
5. Peripheral circuits
5.1. LED’s
The board has 8 LED diodes, which make the simplest interface between the system
and the user. This is especially useful for the beginners, who want to manipulate or
debug their program with different hardware configurations. The diode turns on after
grounding
of the associated LDn (n = 0 – 8) pin.
V dd
R
1 k
L Dn
L ED
L D1
L D2
L D3
L D4
L Dn
4
5.2. Switches
The board is equipped with 4 micro-switches. Pressing one of them causes
grounding of the corresponding pin on the KEY header.
V d d
R
1 0 k
S W n
S n
S W
K EY
S W 1
S W 2
S W 3
S W 4
G ND
5.3. Relay
Access to the relay circuitry consists of the REL pin of the MISC header and pins:
NC, NO, COM of the relay header. REL pin is indirectly connected to the base of the
transistor. Logic level 1 (5 or 3.3 VDC) applied to the REL pin, will activate the relay.
External circuits can be controlled via NC, NO, COM I/O pins.
Vdd
R
4 k7
Q
REL
BC 85 7
COM
D
RL1
RELAY
GND
5.4. Acoustic indicator
The board has an acoustic indicator turned on and off by the transistor. The base of
the transistor is connected to the SPK pin of the MISC header. Logic level ‘1’ (5 or
3.3 VDC) applied to the SPK pin, will activate the buzzer.
Vdd
R8
4k7
Q2
BC 557
SPK
SPK
GND
BUZER
5
Plik z chomika:
mikroprocesory
Inne pliki z tego folderu:
ADPmegaXXX_en.pdf
(67 KB)
AVR JTAG ICE User Guide.pdf
(539 KB)
EVBavr02_en.pdf
(640 KB)
EVBavr03_en.pdf
(663 KB)
EVBavr05_en.pdf
(604 KB)
Inne foldery tego chomika:
ARM
ARM Tools
AVR programy
AVR toolchain
EVB100
Zgłoś jeśli
naruszono regulamin